As soon as you need sound in a lobby, a restaurant, a gym or a string of rooms across several floors, classic low-impedance sound reinforcement hits its limits. Running thick cable to each speaker, watching the impedance of every group, working out the voltage drop over long distances: it gets unmanageable fast. The 100 V line solves it in one move, borrowing the principle of the power grid. It is also called a constant-voltage line, or a 70 V line in North America.
The principle, borrowed from the power grid
Why is electricity transmitted at high voltage? Because at a given power, a higher voltage means a lower current, so fewer losses in the cables and thinner conductors. The 100 V line applies exactly that idea to audio. Instead of putting out a few volts into low impedance, the amplifier raises the signal to a reference voltage: 100 V at full level (or 70 V, or 50 V depending on region and standards). Each speaker carries a small transformer that steps that voltage back down to what its driver needs.
The current flowing in the line is low, so the cable can stay thin even over hundreds of metres, and the voltage drop stays negligible. That is precisely what makes these lines a must for background distribution and public address over large areas.
The power tap, the real adjustment
Here is the most visible difference from regular PA. On a 100 V line, each speaker has a transformer with several taps, labelled in watts: 6 W, 15 W, 30 W, sometimes more. You choose, speaker by speaker, how much power it draws from the line, simply by selecting the tap. A speaker above a noisy table takes 30 W; one in a quiet corridor takes 6 W. The level of each zone is set at install time, without touching the amplifier.
The sizing rule is clear: add up the power drawn by every speaker, and stay under the amplifier’s rated power, with headroom. If your amp delivers 240 W on its 100 V output, you can hang, say, eight speakers set to 30 W, or any mix of taps that stays under that total. Keep 20 to 25 % in reserve: it avoids overloading the line and leaves room to add a speaker later.
100 V, 70 V, 50 V: the same idea
The difference between a 100 V line and a 70 V line is only a matter of reference voltage, tied to local standards and electrical safety rules. Europe mostly works at 100 V; North America, for regulatory reasons, uses 70 V (really 70.7 V). The principle, the transformers and the wiring are identical. A transformer rated for 100 V will deliver less than its stated power on a 70 V line, since the voltage is lower: keep that in mind when you reuse gear from another market.
What the 100 V line does well, and what it does not
These lines shine at distribution: background music, announcements, public address, even coverage of a large space with many points. The wiring is simple, often daisy-chained from one speaker to the next, and adding a point needs no full recalculation.
The transformer, though, has a sonic cost. It colours the signal, limits low-frequency bandwidth and adds slight distortion, especially on cheap models. For high-fidelity reinforcement, a concert, a club or a main PA, you stay low-impedance, with the speaker coupled directly to the amp. That is where choosing how to match amplifiers and speakers by power and impedance, the role of the loudspeaker management processor, and, for large rigs, bi-amplification come in. The 100 V line and low impedance are not rivals: they answer two different needs, and a single venue often mixes both.
A few field traps
- The silent overload: too many speakers, or taps set too high, and the amp goes into protection or runs hot. Always count the sum of the taps.
- The line short: on a daisy chain, one faulty speaker can kill the whole branch. A line impedance tester helps diagnose it.
- Polarity: keep the wiring consistent between speakers, or you get phase cancellation in the zones that overlap.
- Fire safety: in public venues, public address and voice evacuation follow strict standards; the 100 V line rules there, but sizing and wiring must comply.
And as always in distributed sound, a clean cabling plan is worth its weight in gold. The patch and labelling reflexes from stage work apply just as much to a fixed install.
My take
The 100 V line is not glamorous, but it is one of the most elegant ideas in pro audio: solving a distribution problem with a century-old electrical trick. To cover a large space with many points, nothing is simpler or more reliable. You just accept the transformer’s compromise and count your power taps correctly. The moment you want the fidelity or the level of a real main PA, you go back to low impedance. Knowing both means picking the right tool instead of forcing one.